Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

基准信号的低相噪声长距离光纤传输设计

介绍了基准光传输设备的基本组成和原理,指出低相噪长距离光纤传输中的问题所在,并提供了解决问题的方法,即数模混合器件的选择及改进滤波器设计.     

The improvement of electro‐optical properties of polymer‐dispersed liquid crystals with graft copolymer matrix synthesized by reversible addition–fragmentation chain transfer and atom transfer radical polymerization

Aiming to decrease the memory effect of polymer‐dispersed liquid crystals (PDLCs), a type of graft macroinitiator, synthesized by reversible addition–fragmentation chain transfer and atom transfer radical polymerization, was employed to prepare PDLCs with graft copolymer matrix in our previous work. Compared with linear copolymer matrix PDLCs prepared using a linear macroinitiator, it was found that, although low‐memory‐effect PDLCs were obtained, the driving voltage and transmittance of the PDLCs were unfortunately sacrificed to some extent. Thus, it is necessary to improve the electro‐optical properties of PDLCs on the basis of the original research performed by us. In the work reported in this article, a kind of linear macroinitiator with high refractive index and another graft macroinitiator with flexible branched chains were employed to prepare PDLCs. The results showed that by using mixed macroinitiators, the electro‐optical properties of PDLCs could be improved, and a possible mechanism is proposed.     

Synthesis and characterization of novel hyperbranched fluorescent polymers that can be precisely used for metal ion detection and quantification

Four novel hyperbranched polymers with 4 or 5 ring-closed rhodamine units in each were achieved through RAFT polymerization followed by modification with rhodamine moieties. The solubility, thermostability, and photophysical properties of the polymers were studied. The polymers showed high selectivity and sensitivity to Fe³⁺ among various metal ions in CH₃CN/H₂O (75/25, v/v) and could signal Fe³⁺ through multichannels: emerging a new absorption around 558 nm, over 30 nm fluorescence redshift and significant fluorescence enhancement (including 33–37 folds in intensity and 8.3–12.8 folds in quantum yield), accompanied by visual and fluorescent color changes. The polymers could be applied in the analysis of Fe³⁺ in real water samples. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48933.     

Effect of chlorination and fluorination of benzothiadiazole on the performance of polymer solar cells

In order to explore the effects of chlorine and fluorine on photophysical properties and the differences, in this work, we synthesized five new polymers, P1 – P5 , in which benzo[1,2-b:4,5-b]dithiophene as the electron donating and benzothiadiazole as electron withdrawing. Analysis of these five polymers showed that the introduction of Cl and F atoms can deeper the highest occupied molecular orbital of these polymers and enhance the absorption of light by the species, thereby improving V_oc and J_sc. Chlorination has a stronger ability to reduce energy levels and broaden the absorption spectrum compared to fluorination. Among them, P2 showed an efficiency of 4.08% with J_sc of 11.28 mA/cm², V_oc of 0.79 V, and fill factor (FF) of 0.45. Since chlorination is easier than fluorination in terms of synthesis, it is advantageous for practical applications. Therefore, we think that chlorination should not be ignored when designing high efficiency photovoltaic materials, especially when their fluorinated counterparts have proven to have good properties.     

Development of non-enzymatic ZnO nanocomposite-based optical sensor for l-lactate detection in tomato samples

l -lactate is a conjugate base of α-hydroxy acid, a key organic chemical in food processing, fermentation, biology and chemical industries. We are reporting for the first time a facile and rapid non-enzymatic nanosensor for l -lactate detection in tomato-based products using 3-aminophenylboronic acid (3-APBA)-added zinc oxide nanoparticles (ZnO NPs). 3-APBA-functionalised ZnO NPs have a selective and stable SPR intensity change at pH 5.5 to 7.5 and forms a reversible ester with bound l -lactate revealing the wavelength shift from λ = 300 nm to 288 nm in UV-VIS absorption spectrometry. In the spiked (2.5–20 mm ) samples of tomato puree, absorption peak increased as per l -lactate addition with the lower detection limit of 3.98 mm . l -lactate binds with a trigonal form of 3-boronate, thereby generating the tetrahedral complex. ZnO NPs stabilise the tetragonal complex. Nanosensor validated with standard HPLC. This method is useful for l -lactate detection and alternates to conventional techniques.     

A neural network based technique for vibration characterization using Gaussian laser beams

This paper presents a neural network technique combined with an optical measurement system for the characterization of mechanical vibrations in industrial machinery. In the proposed system, the Gaussian beam of a laser source illuminates on an array of photodetectors. If either the laser source or the photodetector array is coupled with a vibrating system, then the optical powers detected by the photodetectors will vary accordingly, and are expected to reflect the magnitude and frequency of the X–Y planar vibrations of the monitored system. The time-varying optical powers are input to an artificial neural network-based vibration monitoring system which maps the power distributions to the X–Y position of the laser beam center. An experimental setup of the system is built and used for training and testing purposes. The obtained experimental results demonstrate the adequacy of combining optical techniques with neural networks to estimate the vibration frequency and magnitude. Estimated frequencies were within 1% of the actual ones, and the estimated magnitudes were within 29% of the actual magnitudes when using a chirp signal in the training phase. The magnitude estimation percentage error was further reduced below 12% when the neural network was trained with a decaying chirp signal.     

Tunable‐focus negative poly(vinyl chloride) gel microlens driven by unilateral electrodes

Tunable‐focus microlenses are urgently required for compact optical products to replace digital zoom and obtain high‐quality images. An electrically controllable tunable‐focus negative microlens is proposed, which is based on an electroactive poly(vinyl chloride) gel plasticized by ecofriendly dioctyl terephthalate. The anode and cathode of the microlens are simply assembled on the same side of the electrorheological elastomer, which greatly saves space and allows the thickness of the proposed microlens to be less than 1 mm. By applying voltages ranging from 0 to 1000 V, the stable focus of the microlens is interestingly able to vary as wide as from –∞ to ?21.3 mm correspondingly. The proposed microlens is simple and thin but is flexible and stable and has a wide range of the focus variation, showing promising applications in minielectric and optical devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46136.     

Influence of Mg concentration on structural,morphological and optical properties of nanoceria

Nano crystalline pure and Mg doped ceriaparticles were synthesized by simple chemical co-precipitation method using cerium nitrate hexahydrate as a source material and magnesium nitrate as doping precursor at room temperature. The effect of doping were investigated by X-ray diffraction pattern(XRD), FT-Raman,fourier transform infrared spectroscopy(FTIR), Ultraviolet spectroscopy(UV), photoluminescence spectroscopy(PL), field emission scanning electron microscope(FESEM) and high resolution transmission electron microscopy with energy dispersive spectroscopy (HRTEM &EDS). The X-ray diffraction pattern and FT-Raman studies showed that the prepared samples were nano particulates with cubic fluorite structure. The XRD pattern analysis showed that the size of the particles ranged from 13 to 20?nm, however 4?wt% Mg doping results in reduction of particle size compared with other doping concentrations. The effects of Mg concentration on various structural parameters of the prepared samples were also determined. The slight blue shift observed upon doping in UV–Vis absorption region around 330–360nmrecorded for reduction in particle size. The FTIR unveils the presence of Metal oxygen bonds below 700?cm^?1in the prepared samples. All samples showed a broad emission band at 430?nm with linearly increasing intensity with respect to dopant concentrations. The Spherical morphology with weak agglomeration was identified through FESEM and HRTEM analysis. The elemental analysis of Ce, O and Mg were confirmed through EDS analysis.     

Polymers beyond standard optical fibres – fabrication of microstructured polymer optical fibres

This paper reports the overall fabrication process of microstructured polymer optical fibres (mPOFs). mPOF fabrication involves a two‐step process: on the one hand, the design and creation of a preform containing a large‐scale version of the desired fibre and, on the other, the precise heating and drawing of the preform to the final fibre. The preforms are produced either by an improved drilling technique or by capillary stacking. For a correct and accurate drawing of the fibre, a controlled and precise heating unit has to be designed, an issue that will be explained in detail in this work. The quality and optical performance of the final mPOF depends strongly on key factors such as the preform annealing, the accuracy of the technique selected for the creation of the preform structure, the heating stage, as well as on the drawing parameters. All of them are analysed in detail and some drawn mPOFs of interest are reported as well. © 2018 Society of Chemical Industry